Free Floppy bunny ears pattern

With only a week until Easter Sunday, I thought I would share the pattern for these Easter bunny ears I made yesterday. I was making a little newborn bunny photo shoot outfit and needed some cute floppy bunny ears to complete the look. I am using my Baby Bear Bonnet Pattern and my own diaper cover pattern which I have just not had chance to write up yet!

They are super simple to make. I used Stylecraft special Aran weight yarn in grey and cream and a 5mm hook and my finished floppy bunny ears measure approx.16cms long.

The outer ears are worked in the round, with the inner ears worked in rows and made separately then sewn into place. My pattern is written using UK terminology but I have provided a US stitch conversion below. Please note chain stitches do not count as a stitch unless otherwise stated in the pattern.

Processing…

Success! You're on the list.

Whoops! There was an error and we couldn't process your subscription. Please reload the page and try again.

Stitch abbreviations as follows

Htr – half treble crochet (UK) / half double crochet (US)

htr2tog – decrease (UK) / hdc2tog – decrease (US)

slst – slip stitch

ch – chain stitch

dc – double crochet (UK) / Single crochet (US)

Outer Ear – Make 2

Ch2

Round 1: 6htr into 2nd ch from hook, join with a slst into top of 1st htr, ch1 . ( 6htr see pic 1.)

Round 2: 2htr in each st around, join with a slst into top of 1st htr, ch1. (12htr see pic 2.)

Round3: *2htr in next st, 1 htr in next st* repeat around, join with a slst into top of 1st htr, ch1. (18htr see pic 3.)

Round 4 – 9: htr in each st around, join with a slst into top of 1st htr, ch1. (18htr see pic 4.)

Round 10: htr2tog, htr in next 14sts, htr2tog, join with a slst in top of 1st htr, ch1 (16htr)

Round 11: htr2tog, htr in next 12sts, htr2tog, join with a slst in top of 1st htr, ch1 (14htr)

Round 12: htr2tog, htr in next 10sts, htr2tog, join with a slst in top of 1st htr, ch1 (12htr see pic 5.)

Rounds 13 – 17: htr in each st around, join with slst in 1st htr, ch1 (12htr see pic 6.)

Round 18: htr2tog all around, join with a slst in 1st htr, ch1 and turn (6htr)

Now flatten circle and slst edges together, fasten off and leave an extra long tail for sewing…longer than you normally would, trust me here as you will need the extra length later! (see pic 7)

Inner Ear is made in rows

make 2

In cream

Row 1: ch4, htr in 2nd ch from hook and in each st along, ch1 and turn (3htr)

Row 2: 2htr, htr, 2htr, ch1, turn (5htr)

Row 3: 2htr, htr in next 3sts, 2htr, ch1, turn (7htr)

Row 4 – 6: htr in each st, ch1, turn (7htr)

Row 7: htr2tog, htr in each st along, ch1, turn (6htr)

Row 8: htr2tog, htr in each st along, ch1, turn (5htr)

Row 9 -11: htr in each st, ch1, turn (5htr)

Row 12: htr2tog, htr in each st, ch1, turn (4htr see pic 8.)

Row 13: htr in each st along, ch1, turn (4htr)

slst all around inner ear to finish, fasten off and leave a long tail for sewing. Sew to outer ear (see pic 9)

To attach bunny ears to chosen bonnet/hat I found that giving the top of the ear a twist and securing with a couple of stitches, gives the ear a little bounce and allows the inner ear to peek out. If the ear is not twisted before attaching to bonnet / hat then you will not be able to see the inner ear…which seems a shame, been as you have just gone to the effort of hooking them. See Pic 10 to see where to twist and sew (indicated by red dots).

Finally pin and securely sew your bunny ears to your bonnet. If you prefer a hat why not checkout My Best Beanie Pattern available in sizes newborn to large adult.

Now all that’s left to do is enjoy all of that floppy bunny ear cuteness!

Please do let me know what you think by dropping me a sentence in the comments below…I love to get your feedback and a like or a share goes a long way too!

Happy Hooking!